COMFAST Wifi Repeater WIFI6 AX1800 2.4Ghz 5G Gigabit Extender 4 Antenna WPA3 OFDAM 11AX Wi-Fi Signal Amplifer Home Repetidor

Description:

WL-NE3602 is a 1800Mbps dual-band WiFi6 signal amplifier.

Equipped with 4 high-gain antennas for signal enhancement,

The house is too big (duplex, large flat, villa, office) and the routing coverage is not complete? Sometimes there is no signal in the corner of the balcony,bedroom, floors, restroom, garage and garden ?

Use with a router to eliminate dead spots of WiFi signals at home, effectively expand WiFi coverage, and ach.

Pls Note:

Don’t use to compare the wifi speed with router’s, it would be useless, don’t buy on this purpose.

Key Features:

• Wi-Fi expands and eliminates dead spots of wireless signals;

•1800Mbps Gigabit Dual Band WiFi6 Repeater Amplifier,360° Full Coverage;

• 1800Mbps Dual Band 2.4G/5GHz :Connect to both 2.4GHz and 5GHz Wi-Fi bands for faster and more stable internet speeds;

• 802.11AX Gigabit Wireless Extender :The latest Wi-Fi standard ensures lightning-fast internet speeds and reliable connectivity;

• Wired Transfer Rate 10/100/1000Mbps :Connect to your internet source with high-speed wired internet for faster and more reliable internet speeds;

• • Wireless Repeater :Repeat your existing Wi-Fi signal to provide coverage in hard-to-reach areas.More compatible with WiFi6 home routing;

• 4 antenna signal enhancement, signal coverage and wall penetration are significantly improved;

• The antenna can be flexibly rotated, and the user can adjust the antenna angle to adjust the signal transmission and reception;

• Support Wi-Fi to wired, can be connected to TV, computer, etc. to connect to wired and work stably;

•With various modes, you can either use it as a regular extender/AP ;

•The WiFi 6 MU-MIMO and OFDMA techniques have largely improved the device efficiency and performance.

• Scientific heat dissipation design, the device supports 24h stable work without disconnection, avoiding overheating and aging of components;

Specification:

Model WL-NE3602;

Support IEEE802.11a/b/g/n/ac/ax standard;

Memory: 128MB; Flash: 16MB;

Maximum transmit power: 200mW (≈23dBm);

Maximum receive sensitivity: -96dBm Operating

frequency: 802.11b/g/n: 2.412GHz-2.472GHz; 802.11ax/ac/an/a:

5.180GHz- 5.825GHz

1*10/100/1000Mbps RJ45 WAN/LAN Ethernet port;

RESET and WPS share 1 key;

2.4GHz: 574Mbps; 5.8GHz: 1201Mbps

Antenna gain: 4*2dbi external antenna

Power parameters :100~240V, 50/60Hz

Maximum power consumption : ＜15W

Support AP, relay, routing mode;

Need the WiFi signal is amplified, select the repeater mode;

Analog router use, selectable routing mode;

The repeater is too far from the main route, choose AP mode;

Packing list:

1*WL-NE3602 WiFi 6 Router Repeater

1*Network cable

1*Instruction manual

8 Reasons to Choose CF-XR182:

Wi-Fi6:The new generation of WiFi

Tri-Core CPU:High-performance processing without delay

1800Mbps:Dual-band / high-speed

Gigabit port:Fully use of the bandwidth

OFDMA:Data transmission for multiple devices

WPA3 Encrypt:Safer and more secure than WPA2

Signal Wall-through :4 pieces high gain antennas

Multi-functions:Support AP/Repeater/Router Mode

1800Mbps Dual-band WiFi Speed

With the 802.11AX technology, CF-XR182 can easily extend the WiFi range for your gigabit dual-band WiFi router,providing an enjoyable WiFi experience.

PS: In theory, 1800Mbps (2 4GHz 600Mbps + 5.8GHz 1201Mbps)

WiFi6 VS WiFi5 ,Al-aspect Improvement

Speed up to 1800Mbps, no dropping, no stuck

Where Will You Needa COMFAST Repeater

1、The big house that one WiFi router can’tcover all area

Usually, A WiFi router can cover 70 square meters area ofyour house, you can add a CF-XR182 to extend theWiFi coverage.

2、Multi-layer house, long distance betweenupstairs and downstairsA CF-XR182 can provide a stable and reliable WiFi signalno matter where you are.

3、Extend the WiFi of your neighbor

CF-XR182 can extend the WiFi range of your neighbor who isaway on a business trip.

4 High Gain Antennas

Good Signal in Long Distance

Designed with 4 Omni-directional antennas for better performance of wall-through and anti-interference, also for wider WiFi coverage and faster data trans-receive speed.

PS: The antennas are an advertising effect drawing,and the internal structure is not fully displayed. Please refer to the real object.

Effective Heat Dissipation

Longer Lifespan

The heat sink hole design can keep the WiFi repeater away from the components aging and unstable operation caused by high heat.

All Gigabit Ethernet Port

Equipped with a gigabit Ethernet RJ45 WAN/L AN port,which can make full use of the bandwidth from most ISP.

Plug and Play after first setting

Multiple Mode for Different Situation

01.Repeater Mode (wireless to wireless)

Extend the main router’s WiFi signal to every corner of the house

02.AP/Router Mode (Wired to Wireless)

Wired connection between the main WiFi router and WiFi repeater

03.Wireless to Wired

CF-XR182 has an RJ45 Ethernet port supporting

a wired connection with the desktop or laptop.

Q&A

Q1: Can’t connect to internet after finished setting ?

A1: Please check whether you enter the same password as your router, and check is there any special characters in it, such as *&^%$#@!. If yes, please change your router password. Repeater can not identify special characters.

Q2: How to reset the repeater ?

A2: Please long press the reset button for 10 seconds under powered.

Q3: What is the coverage of repeaters?

A3: The range of the wifi repeater is about 10-20m

Q4: Why does the wireless transmission rate speed down,when the wirelesssignal! is stronger after repeated by the Repeater?

A4:Repeater has to process one-way communication between your root Wireless

In compliance with the wireless transmission protocol,all the Repeater devicesare set to work in half-duplex instead of full-duplex mode.In other words,therouter(or AP) and the terminal clients; so the transmission time will be double-increased,while the speed will be decreased.Recommends that youconnect to the extender when your home network connection is poor ,or whenyou want a larger wireless coverage to eliminate’ dead zones”

Q5: Why the devices connected to the Repeater cannot get an IP addressfrom the Repeater and cannot access the Internet?

A5:

①Maybe you enabled a wireless for MAC filter ,wireless access control,or accesscontrol list(ACL) on your router. To solve this problem,please log into yourrouter and disable the for MAC filter,wireless access control or ACL.

②Maybe the Repeater has not been successfully connected to your router,please reset the Repeater and Reconfiguration.

③Maybe the IP address of the router is occupied or the wireless device connected by the router has reached the limit. please reboot your router,then reset the Repeater and Reconfiguration.

Q6: After the repeater is set, unplug or power off, do I need to reset it?

A6: No need to reset, the original configuration information is saved unless you manually restore the factory state.

Q7: Does it work with the other brands Router ?

A7: Our Repeater work with most routers on the market ,It work best with comfast wireless router.

Q8: Does a wifi repeater booster wifi speed?

A8: A wifi repeater expands the coverage but can not boost wifi speed

Q9: There are many rooms in the house, is one repeater enough?

A9: If you need to fully cover the WiFi signals in multiple rooms, you need to add an appropriate number of repeaters based on the specific environment.

Q10: What is the wifi speed of this repeater ?

A10: The Speed is depend on the main router. If your router is dual band 2.4G & 5G wifi signal, this mode repeater can received 2.4G  and 5.8G wifi signal, and give 2.4G and 5.8G wifi speed.

Q11: What is the difference between 2.4GHz and 5GHz?

A11: 2.4GHz: The penetration is good, the transmission distance is much greater than 5GHz.

5 GHz: The speed is faster than 2.4 GHz, but the penetration is not better than 2.4G, the speed is reduced by half when there are barriers such as walls between extenders and devices.

Q12:What should I do if I cannot access the Repeater’ s web managementpage?

A12:

①Make sure your computer is connected to the extended network.

② Make sure your computer is set to obtain an IP address automatically.

③ If the Repeater has connected to the router,you should go to your router’ sDHCP client list to obtain the Repeater’ s current IP address.

④ Reset the Repeater.